1242 / 1575
SAFARI 400NM
SR
NO
DTC
FTB
DESCRIPTION
CAUSES
EFFECT ON VEHICLE
CHECK
POINTS
CORRECTIVE ACTION
MIL
STATUS
CEL
50
P0201
1A
Circuit resistance Below
threshold
1.
This DTC gets logged, if wiring
harness resistance of Injector in
cylinder 1 is below the lower threshold.
EMS ECU takes following
recovery actions:
1.
Disables the BRC reading and use
estimation for injector pulse
duration instead of reading for inj
cylinder 1.
2.
Disables RVD(Rail Valve
Discharge) on injector cylinder1.
3.
Disables PWC strategy (Pilot main
waves compensation).
4.
Applies reduce torque mode:(80%
of torque).
5.
Disables SPC(Speed Pilot Control)
strategy, no more SPC (Speed
Pilot Control) trim update.
1.
Check injector connector; Key off ignition and wait for 20
seconds. Disconnect the injector clean and reconnect
properly. Check if problem vanishes.
2.
Perform Injector cylinder 1 actuator test with the help of I/O
control command of injector cylinder 1. If this test fails then it
is confirmed that there is some issue with either injector wiring
harness/Injector itself.
3.
Check the wiring harness resistance between the Injector
cylinder 1 connector pin 2 and EMS ECU pin A26, the
resistance value should be less than 0.15 ohm. Check the
wiring harness resistance between the Injector cylinder 1
connector pin 1 and EMS ECU pin A27, the resistance value
should be less than 0.15 ohm. If the resistance found is out of
range then replace wiring harness of injector. check the
resistance between two injector treminals it should be less
than 0.322 ohms.
4.
Check for fault codes - P0201 or P0263 or P2147 or P2148. If
any of these faults appear then resolve these faults by
following thier rectification procedure.
5.
Replace Injector cylinder 1 wiring harness if probblem still
persists.
6.
Replace injector if problem still persists.
7.
Replace ECU if problem still persists.
OFF
ON
51
P0201
1B
Circuit resistance above
threshold
1. This DTC gets logged, if wiring
harness resistance of Injector in
cylinder 1 exceeds the upper threshold.
EMS ECU takes following
recovery actions:
1.
Disables the BRC reading and use
estimation for injector pulse
duration instead of reading for inj
cylinder 1.
2.
Disables RVD(Rail Valve
Discharge) on injector cylinder1.
3.
Disables PWC strategy (Pilot main
waves compensation)
4.
Applies reduce torque mode:(80%
of torque).
5.
Disables SPC(Speed Pilot Control)
strategy, no more SPC (Speed
Pilot Control) trim update.
1.
Check injector connector; Key off ignition and wait for 20
seconds. Disconnect the injector clean and reconnect
properly. Check if problem vanishes.
2.
Perform Injector cylinder 1 actuator test with the help of I/O
control command of injector cylinder 1. If this test fails then it
is confirmed that there is some issue with either injector wiring
harness/Injector itself.
3.
Check the wiring harness resistance between the Injector
cylinder 1 connector pin 2 and EMS ECU pin A26, the
resistance value should be less than 0.15 ohm. Check the
wiring harness resistance between the Injector cylinder 1
connector pin 1 and EMS ECU pin A27, the resistance value
should be less than 0.15 ohm. If the resistance found is out of
range then replace wiring harness of injector. check the
resistance between two injector treminals it should be less
than 0.322 ohms.
4.
Check for fault codes - P0201 or P0263 or P2147 or P2148. If
any of these faults appear then resolve these faults by
following thier rectification procedure.
5.
Replace Injector cylinder 1 wiring harness if problem still
persists.
6.
Replace injector if problem still persists.
7.
Replace ECU if problem still persists..
OFF
ON